Dark Red Meranti

                 

 

Botanical name

Shorea spp.

Origin

Dark Red Meranti grows in the Philippines, Malaysia, Indonesia and Thailand.

Trading names

Dark Red Meranti

Separation into light red meranti and dark red meranti is based more on wood density than on heartwood colour.

The term meranti is applied to a large number of species of Shorea, which is a dominant hardwood genus in Malaysia, Indonesia, the Philippines and Thailand.

The term seraya is common in Sabah, and lauan in the Philippines, for the very similar Shorea timber.

A large number of South-East Asian species are likely to be included under dark red meranti or under alternative names, such as dark red seraya, dark red lauan or oba suluk.

Appearance

Heartwood

reddish brown.

 

Sapwood

distinctly paler sometimes with a greyish tinge.

 

Texture

coarse but even.

 

Grain

usually interlocked producing stripe figure on the radial surface.

 

Pinhole borer discolouration & pencil streak

less common than in light red meranti.

General comment

Slower to dry than light red meranti.

Relatively easy to work although some species may contain a little silica.

Tools need to be kept sharp to avoid producing a woolly surface.

Nails and glues well.

Unsuitable for steam bending.

Common uses

Plywood, internal moulding and joinery, furniture, panelling.

Properties
(See notes below)

Hardness rating

Average Hardness Rating - Dry: Soft


Lyctid Susceptibility of Sapwood

Susceptible
(source AS 5604)


Termite Resistance of Heartwood (inside above ground)

Not resistant
(source AS 5604)


Marine Borer Resistance of Heartwood

Class 4
(source AS 5604)


Natural Durability Rating of Heartwood Above Ground

Class 4
(source AS 5604)


Natural Durability Rating of Heartwood In-Ground Contact

Class 4
(source AS 5604)

 

Notes

Density: 'Green Density' (GD) is the density of the wood at the time the living tree is felled. It varies considerably with the season, weather conditions, the age of the tree and so on; the quoted figure must therefore be accepted as a guideline only and when accurate green density figures are required for, say, assessment of transport costs, it is advisable to carry out accurate determinations on the materials involved.

'Dry Density' or 'Air Dry Density' (ADD) is the average density of the wood at 12 per cent moisture content. It too varies with conditions of growth, climate and maturity of wood.

There are published figures for both Green Density and Air Dry Density of most commercial species.

The figures given above have been rounded to the nearest 50.

Hardness rating: the hardness rating of a timber species is measured by the Janka Test. This is a standard test which measures the penetration into the timber of a common load and projectile. The results relate to a hardness capacity of the material and are expressed in kN. This information is useful where the timber may be subject to potential damage from impacts e.g. a dance floor. There are 2 sets of published figures; one for 'Green' or freshly felled timber and one for seasoned timber - i.e. timber with a moisture content of 12%.

The ratings given here are:
  Soft - less than 5.5
  Moderate - 5.5 to 7.0
  Hard - 7.1 to 10.0
  Very Hard - greater than 10.0.

Lyctid susceptible sapwood: Only the sapwood of some hardwoods is susceptible to lyctid borer attack. No softwoods are susceptible to attack.

Natural durability ratings: The natural durability rating of a timber species is a rating of the timber's resistance to attack by wood destroying fungi and wood destroying insects. The sapwood of all timber species has poor resistance and so the natural durability rating applies only to the heartwood of a timber species. The rating is based on the testing of stakes and poles embedded in the ground and on expert opinion of historical performance. There are 2 sets of ratings: one for above ground use and one for in-ground contact use. The lower the number the higher the performance in terms of durability. This information is useful for specifying material for external or exposed applications.